不卡视频在线一区_日韩精品一区高清电影_动漫无遮挡h纯肉亚洲资源大片_男人天堂视频一区二区_亚洲日韩一区精品射精

當前位置:首頁-新聞資訊

鋁單板鈑金加工的“精確性”怎么確定?

來源:http://www.cettools.cn/ 發布時間:2018-02-23

整個鋁單板工程項目的鋁單板并不是直接按圖紙一次性生產完備,直接交給施工方。而是一批貨一批貨生產完成后,讓施工的工人安裝完備之后,然后再進行下一批次的生產和加工。這就要求鋁單板加工廠家的產品誤差不能太大,起始的一個很小的誤差,則將會使后來的鋁單板加工面臨數據上的難題,產品易遇到安裝不上的難題,正所謂“失之毫厘,謬以千里”。
The aluminum single board of the whole aluminum sheet project is not directly produced in one time according to the drawings, and is directly handed over to the constructor. But after the production of a batch of goods is completed, the construction workers are fully installed, and then the next batch of production and processing. This requires a product error can not be single aluminum plate processing factory is too large, a very small initial error, it will make the later processing of single aluminum plate facing the problem data, easy installation is not the problem, is the so-called "a difference".
在這方面,整個鋁單板加工行業其實是有相關的國家推薦標準,在這個標準中,對相應的參數規定的非常仔細嚴格。通常鋁單板的尺寸、規格是由厚度、長度、寬度、折邊高度、對角線差等組成。長和寬決定了整個鋁單板的基本形狀,而厚度則可以影響著整個鋁板的性能。
In this regard, the whole aluminum sheet processing industry is actually related to the national recommendation standard. In this standard, the corresponding parameters are carefully and strictly regulated. The size and specification of the aluminum sheet is usually made up of thickness, length, width, height of folded edge, diagonal difference and so on. The length and width determine the basic shape of the whole aluminum sheet, and the thickness can affect the performance of the whole aluminum plate.

鋁卷生產廠家
無論鋁單板板型如何,厚度上誤差范圍在±0.1mm以內。當鋁單板長寬尺寸小于或等于2000mm的時候,長度和寬度所允許的較大誤差是1mm。長寬尺寸大于2000mm時,長度和寬度的誤差均不能超過1.5mm。
The error range of the thickness is less than 0.1mm, regardless of the aluminum sheet type. When the length and width of an aluminum sheet is less than or equal to 2000mm, the maximum error allowed by the length and width is 1mm. When the length and width are larger than 2000mm, the error of length and width can not exceed 1.5mm.
折邊高度的誤差范圍與鋁單板板面大小沒關系,永遠不能超過0.5mm。而對角線差所允許的誤差范圍是,當鋁單板長度小于等于2000mm時,允許誤差值為2mm;若長度大于2000mm時,誤差值不能超過3mm。
There is no relation between the error range of the height of the folded edge and the size of the plate surface of the aluminum sheet, and can never exceed 0.5mm. The allowable error range of diagonal difference is that when the length of aluminum plate is less than or equal to 2000mm, the allowable error is 2mm. If the length is greater than 2000mm, the error value can't exceed 3mm.
鋁單板的鈑金加工是在生產線上,由技術工人在機器上進行加工制作,由于各種原因,會使得加工出來的鋁單板可能存在一定的誤差,但這個誤差必須控制在一定的范圍之內,否則即為不合格的產品。這些誤差必須盡可能的減小,完全避免的話則更好!無論是鈑金加工,還是噴涂過程,都必須要注意精確性。
Sheet metal processing aluminum single plate is in the production line, by skilled workers in machine production, due to various reasons, the single aluminum plate makes the processing out there may be some error, but this error must be controlled in a certain range, which is otherwise unqualified products. These errors must be reduced as much as possible and better if they are completely avoided! It is necessary to pay attention to accuracy, whether it is sheet metal processing or spraying process.
相信看了本文的介紹后,對鋁卷生產廠家http://www.cettools.cn這方面也會有自己的一番認識,以后針對的等問題也能很好的解決。
I believe that after reading the introduction of this paper, we will have some understanding of the http://www.cettools.cn of aluminum coil manufacturer, and we can solve some other problems later.

主站蜘蛛池模板: 波多野结衣一区二区三区av高清| 97人妻精品一区二区三区六| 大屁股熟女一区二区 | 无码爆乳护士让我爽| 2022精品久久久久久中文字幕| 亚洲熟女www一区二区三区| 最新av网址在线观看不卡一区二区| 国产色无码精品视频国产| 日本中文字幕视频一区二区三区| 18禁无遮挡羞羞污污污污网站| 欧美日韩一区二区性生活视频| 久久免费区一区二区三波多野| 国产一区二区视频在线免费观看 | 国产又色又爽无遮挡免费动态图| 国产精品视频aⅴ一区二区| 欧美xxx一区二区三区| 夜鲁鲁鲁夜夜综合视频欧美| 亚洲国产日韩在线观看一区| 欧美 国产 日韩一区二区 | 久久久久久久一区二区| 国产一区2区在线观看 | 亚洲成av人一区二区三区| 精品一区二区黄色综合| 久久成人免费精品网站| 国产日韩欧美视频一区二区| 国产成人精品日本亚洲成熟| 杨幂在线91精品一区二区| 熟妇诱惑一区二区三区四区| 亚洲一区二区在线不卡| 国产一区 欧美 日韩| 黄色视频网站在线观看| 十八禁视频网站在线观看| 国产一区二区小视频| 色婷婷av一区二区三区大白胸| 国产精品一区视频日韩| 3d无码纯肉动漫在线观看| 亚洲av区无码字幕中文色| 摸奶视频一区二区| 精品久久久久一区二区| 快播av一区二区三区电影网 | 亚洲一区精品在线|